Step Instruction for Bathtub Installation
Step Instruction for Bathtub Installation
Blog Article
Each person will have their unique conception on the subject of Tools You Need to Install a New Bathtub .
Setting up a bath tub isn't precisely rocket science, but it does require strong plumbing, carpentry, and occasionally, tiling abilities. Changing an old bathtub with a brand-new one is likewise a moderately hard project. If the old tub is easily available, the task can relocate speedily; if you need to open up a wall surface to remove the old tub and also place the new bath tub, the job is much harder. In either situation, the task is within a home handyman's abilities, although you will need a helper to move out the old tub and set in the new one. Make sure you have actually qualified yourself for the work and also fit trying it. Instead of hiring a specialist to take control of a halfway-completed job, it is much better to think about using one before you begin. Possibilities are you may require a specialist plumber to make tube links.
This post will assist you mount a brand-new bath tub in your restroom if you have actually currently purchased a brand-new tub and do not need to transform the arrangement of your previous water pipes.
Your devices as well as product checklist should comprise the following:
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, then the first thing you should do is detach the water. After doing so, switch on the faucets to drain pipes any kind of water remaining in the system. The process of removing the existing faucets can be fairly bothersome because of the limited access that is commonly the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will certainly originate from the pipelines. When the supply pipes have actually been eliminated, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the solitary faucets from transforming throughout this procedure. When the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
Before proceeding to fit the brand-new taps, contrast the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic connector to avoid damage to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly call for decreasing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the mounting opening in the bath/basin making sure that the washing machines remain in location in between the tap and also the sink. Protect the tap in place with the manufacturer given backnut. When the tap is safely in place, the supply pipes can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical tap connectors. The previous type must be linked to the tap ends initially, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Bath tub
Utilizing both wood boards under its feet, position the bath tub in the called for setting. The wooden boards are helpful in equally spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the bathtub until the level reviews degree.
To install taps, fit the bottom of the furthest flexible faucet adapter to the proper supply pipe by making a compression join; after that do the same for the other tap.
Turn on the water system as well as examine all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill up the bath tub and also examine the overflow outlet and also the normal electrical outlet for leakages.
Finally, fix the bathroom paneling as explained in the supplier's user's manual. Tiling as well as sealing around the bath tub ought to wait till the tub has been made use of a minimum of once as this will certainly settle it right into its last placement.
Preparing for the Setup
To start with, the supporting framework provided with the bathroom ought to be fitted (if called for) according to the producer's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is important to make certain that if the tap features a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps system to stop strain on the tub.
Fit the flexible tap ports to the bottom of the two faucets using 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize all of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must now be ready to be suited its last placement.
Tiling Around the Tub
In the area where the bath meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to crack a stiff seal, causing the water to permeate the wall surface in between the bathroom and the tiling, causing issues with moisture as well as possible leakages to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your fixtures and installations. They are marketed in tubes and cartridges, and can securing gaps up to a size of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill the bath tub with water before securing, to permit the motion experienced when the bathtub remains in usage. The sealant can crack rather early if you do not think about this activity before sealing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently readily available on the marketplace. It is advisable to fit the ceramic tiles utilizing water-resistant or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you liked our piece about A Step-by-Step Guide to Installing a Bathtub. Thank you so much for taking a few minutes to read our article. Sharing is nice. Helping others is fun. I am grateful for your time. Visit again soon.
Clog issue? Reach out! Report this page